Online Buck RC Snubber Calculator

Biricha Buck Snubber Design Tool

Enter the required parameters and this online calculator will calculate the snubber R and C values for the Buck converter.

Enter maximum input voltage (Vin)

V

Enter power supply switching frequency (Fs)

Hz

e.g for 100kHz you can type 100000 or 100e3

Low Side Switch (D2/Q2) Snubber Calculations (R_snub2 & C_snub2)

Measure and enter ringing frequency on the rising edge of switch node voltage at point X (Fr0_rising) without snubber

Hz

e.g. for 27MHz you can type 27e6. Note: this is the ringing frequency on the rising edge of the voltage measured at point X in the diagram with respect to ground.

Enter the desired power dissipation in the snubber resistor (R_snub2)

W

e.g. for 50mW please type in 50e-3

For reference typical maximum dissipation for 1 oz FR4 PCB with minimal pad size (check manufacturer datasheet) 1206 package ~ 0.125W to 0.250W 1210 package ~ 0.25W to 0.500W

Calculated first pass snubber capacitor value (C_snub2)

F

Select a capacitor value close to this. After selecting this first pass snubber capacitor value solder this capacitor in place of C_snub2 and temporarily short R_snub2 with a 0R resistor. Then please follow the instructions below.

Enter actual value of C_snub2 soldered

F

e.g. for 400pF please type in 400e-12

Note: If snubber capacitance is too big, power dissipation will be large; if it is too small the circuit will not work well This power will be lost when you solder a snubber resistor.

Estimated power dissipation in the final snubber resistor, R_snub2, as a result of the value of C_snub2 entered above

W

Re-measure and enter the new ringing frequency after the addition of C_snub2

Hz

Estimated effective Coss of the switch

F

Estimated effective leakage inductance (L_lkg)

H

Recommended Snubber Resistance (R_snub2)

Ω

Note 1: Use as close a value as possible Note 2: To finalize your design, look at the ringing again. Ideally there should be only 1 or no undershoot. If this is the case, you may be able to reduce C_snub2 and check to see if you can reduce your losses

High Side Switch (Q1) Snubber Calculations (R_snub1 & C_snub1) Note: Often you do not need this after soldering the low side snubber. Make sure the low side snubber is in the circuit and functioning before adding this high side snubber.

Measure and enter ringing frequency on the falling edge of switch node voltage at point X (Fr0_falling) without snubber

Hz

e.g. for 90MHz you can type 90e6. Note: this is the ringing frequency on the falling edge of the voltage measured at point X in the diagram with respect to ground.

Enter the desired power dissipation in the snubber resistor (R_snub1)

W

e.g. for 50mW please type in 50e-3

For reference typical maximum dissipation for 1 oz FR4 PCB with minimal pad size (check manufacturer datasheet) 1206 package ~ 0.125W to 0.250W 1210 package ~ 0.25W to 0.500W

Recommended first pass snubber capacitor value (C_snub1)

F

Select a capacitor value close to this. After selecting this first pass snubber capacitor value solder this capacitor in place of C_snub1 and temporarily short R_snub1 with a 0R resistor. Then please follow the instructions below.

Enter actual value of C_snub1 soldered

F

e.g. for 360pF please type in 360e-12

Note: If snubber capacitance is too big, power dissipation will be large; if it is too small the circuit will not work well This power will be lost when you solder a snubber resistor.

Estimated power dissipation in the final snubber resistor, R_snub1, as a result of the value of C_snub1 entered above

W

Re-measure and enter the new ringing frequency after the addition of C_snub1

Hz

Estimated effective Coss of the switch

F

Estimated effective leakage inductance (L_lkg)

H

Recommended Snubber Resistance (R_snub1)

Ω

Note 1: Use as close a value as possible Note 2: To finalize your design, look at the ringing again. Ideally there should be only 1 or no undershoot. If this is the case, you may be able to reduce C_snub2 and check to see if you can reduce your losses

Your design is complete! 🙂 Please vist our workshops page to find out about our face-to-face and online workshops.